| Electrical setup | ||||
| 001 | 3x 400 V | S | ||
| 004 | 50 Hz | S | ||
| 11 | 15.0 HP (11.0 kW) sanding motor with sanding module | S | ||
| 12 | 20.0 HP (15.0 kW) sanding motor with sanding module | O | ||
| 13 | 25.0 HP (18.5 kW) sanding motor with sanding module | O | ||
| 14 | 2 motors, each with at 15.0 HP (11.0 kW) for FW 1102 | O | ||
| 10 | STAR-delta-START | S | ||
| Ampage meter for monitoring the electrical load on the units | S | |||
| Automatic sanding-belt brake | S | |||
| Sanding unit and sanding cushion | ||||
| Combination unit CU (contact roller and sanding cushion), sanding pad toughness 45° Shore | S | |||
| Contact-roller unit C, sanding pad with a toughness of 85° Shore | S | |||
| Easily and quickly exchangable stiff sanding pad | S | |||
| 300 | Electro-pneumatic sanding cushion EP | O | ||
| 400 | Segmented, electro-pneumatic sanding pad ESC, touchscreen included | O | ||
| Sanding width 1100 mm | S | |||
| Sanding height 3–170 mm | S | |||
| Sanding belt is oscillated electro-pneumatically | S | |||
| Electronic run-off protection for the sanding belt | S | |||
| Pneumatic tensioning of the sanding belt | S | |||
| Sanding belt 1110 x 1900 mm (width x length) | S | |||
| 19 | Activation and deactivation of the first sanding module from the control panel | O | ||
| 20 | Activation and deactivation of the second sanding module from the control panel | O | ||
| 21 | Variable cutting speed control from 2.4–19 m/sec (available for 15.0 HP (11.0 kW) motors) | O | ||
| 22 | Variable cutting speed control from 2.4–19 m/sec (available for 20.0 HP (15.0 kW) motors) | O | ||
| 23 | Pressurised air cleaning module with timer | O | ||
| 25 | Brush unit at outfeed end, Ø 150 mm, incl. brush (!26) | O | ||
| 26 | Brush unit “Scotch Brite” at outfeed end, Ø 150 mm, incl. brush | O | ||
| 29 | Special wood structuring group, Ø 150 mm, motor power 4.2 kW, incl. brush K60 | O | ||
| Feeder table | ||||
| Electronic height control for the table | S | |||
| Digital display shows the height of the feeder table | S | |||
| 16 | Variable feed speed 3.7–16 m/min, adjusted using the handwheel | S | ||
| 17 | Inverter controlled variable feed speed of 2.8-20 m/min, selected from the control panel | O | ||
| Mechanical vibration-absorbing rubber pressure rolls | S | |||
| Hand guard and over-thicknessing protection for the workpiece | S | |||
| 18 | Workpiece thickness sensor | O | ||
| 28 | Vacuum table for FW 1102 with 5.5 HP (4.2 kW) fan | O | ||
| 32 | Vacuum table for connection to workshop dust extraction, without fan | O | ||
| General | ||||
| Machine packing dimensions in mm (length x width) | 1680 x 1550 x 2150 | |||
| Extraction connector Ø in mm | 2x 160 | |||
| Weight kg (with standard configuration) | 1550 | |||
| Important Accessories | ||||
| 85 | 300 mm table extension with roller, can be used on both sides of the sanding table | O | ||
| Transport | ||||
| 221 | Preparation for container | O | ||
